|
Kreg RAC Right Angle Clamp | 
| Brand: Kreg
Category: Home Improvement
List Price: $24.99
Buy New: $22.44
You Save: $2.55 (10%)
Rating:  14 reviews
Media: Tools & Hardware
Shipping Weight (lbs): 1.7
Dimensions (in): 13 x 5.9 x 0.6
MPN: RAC
Model: RAC
UPC: 647096352158
EAN: 0647096352158
ASIN: B00009OLD3
Shipping: Eligible for Super Saver Shipping
Availability: Usually ships in 24 hours
| |
| Features:
| • | Securely holds work pieces at a 90 degree angle | | • | Two arms swivel to adjust to work piece dimensions and anchor work pieces | | • | 4-1/2 inch reach for added flexibility | | • | Easy release handle simplifies operation |
|
| Editorial Reviews:
Product Description
Attaching a face frame to a cabinet carcass, assemblng drawers, shelving and other situations where you need to join workpieces at 90 angles is a snap with the right angle clamp. It features a steel pin on one arm that fits snugly into 1 pocket hole to cl
Amazon.com Product Description
The Kreg Right Angle Clamp holds work pieces at a 90 degree angle. It has a steel dowel on one arm to fit into the pockethole and anchoring your work piece against the second work piece to be joined. An opposite arm has a 180 degree swiveling pad that automatically adjusts to the dimensions of the work piece while you finish the joint by driving a screw into the adjacent pocket hole. This clamp with a 4-1/2-inch reach and easy release handle is particularly useful for assembling box joints and joining a cabinet carcass to face frames.
|
| Customer Reviews: Read 9 more reviews...
 No substitute for this tool August 18, 2008
New England Yankee (New Hampshire)
This clamp works flawlessly every time. Conceptually, it's very simple. It replaces one of the flats on a normal Kreg clamp with a pin that fits in the pocket hole. Use the clamps in one or more pocket holes while you drive the screws into the others. If you need 100% square accuracy, you can hold a square in place against the joint while you drive the screw.
By the way, you can use these to clamp items that are not flush to one another, e.g., frame reveals, parts with differing thicknesses, and inset panels. Try THAT with a corner clamp!
To the reviewer that wondered about using pocket holes on the outside of items: In cabinet making, it's the INSIDE of the cabinet that's the concern. The ply or particleboard sides and back of the cabinet are completely hidden for most cabinets and virtually always covered on end cabinets.
As to the review that talks about blowing out the pocket hole, the only things that could possibly cause that are drilling too small a pocket (the clamps work perfectly with Kreg drills), clamping so tight as to crush the pocket, or clamping at an extreme angle (the clamp will work at a range of angles, not just 90 degrees). Or perhaps the owner has a defective clamp. In any event, this is a highly unusual complaint, and I've yet to hear from anyone else with this problem. Trust your own judgement, though, go to a demo at a woodworking show or store and try them.
Can find this elsewhere for cheaperG August 4, 2008
M. Schurr
This is a great product but if you look around you can find this clamp cheaper.
Work great when drilling February 22, 2008
Electric Z (Aloha Oregon)
1 out of 1 found this review helpful
I bought two of these clamps and glad I did. On occasion, I use to hold the wood in place on both ends or at a corner. I can drill a hole, clamp it then drill the other end and/or adjoining board, knowing the boards are going to be precisely in place when I put in the screws. Now its not moving.
The quality is good and will last a long time. It is amazing to me still how well they can hold at a right angle. It really works!
I easily recommend these and they make the finishing touch just a little easier for me.
Right Angle Clamp February 11, 2008
B. R. Barefoot (Fayetteville, NC USA)
Great clamp for Kreg's pocket screw holes. I order the extra clamp to go with the kit I purchased earlier. Good buy
 works amazingly well January 14, 2008
M. Salmon (Atlanta, Ga)
The RAC makes a creating a tight flush joint a snap. It actually is better then a second set of hands unless those hands can press 350lbs. A second clamp would be a good idea on larger projects. I was frustrated as the spring fell off a few times at first but I took care of it and it works fine now.
|
|
|
| |
