|
Jet JW1015 4-Inch Y-Fitting Dust Hose Connector | 
| Brand: Jet
Category: Home Improvement
Buy New: $6.40
Rating:  4 reviews
Media: Tools & Hardware
Shipping Weight (lbs): 0.9
Dimensions (in): 10 x 8.5 x 3.8
Model: JW1015
UPC: 662755122255
EAN: 0662755122255
ASIN: B00005A1I8
Shipping: Eligible for Super Saver Shipping
Availability: Usually ships in 24 hours
| |
| Features:
| • | Versatile Y-branch for branching off main lines | | • | Allows you to gradually split the main line more efficiently than a T-branch | | • | Can also be used as a clean-out | | • | Slightly undersized to fit inside the hose | | • | Overall size measures 9-13/16-by-4-1/16-by-8-1/4-inches |
|
| Jet 4" Dust Collection Accessories:
|
| Editorial Reviews:
Amazon.com Product Description
The Jet 4-Inch Y-Fitting Dust Hose Connector is designed for attaching branch lines to service more than one machine. The featured Y-branch design provides increased lateral airflow and efficiency when compared to traditional T-branches. The 4-inch diameter fitting can also be used as a clean-out, and is slightly undersized to fit inside the hose.
|
| Customer Reviews:
Y Dust Hose Connector July 3, 2007
Kenneth N. Swezey
1 out of 1 found this review helpful
This product is as described! Connected two tubes and made into one tube!! Used as a two tube converter to a one tube converter.
Great DC fitting! July 12, 2006
Scott Pointon (Crest Hill, IL United States)
7 out of 7 found this review helpful
Like all of my Jet dust collector fittings, I have been very pleased with the performance of this "Y" fitting, and it was much MUCH cheaper at my local Menards. I used these Y's in my main duct to create branches for my stationary tools on the long wall of my shop. The 4" size was perfectly consistent and always fit the ducting and flex hose without any trouble. The "Y" design greatly reduces any loss of air flow as compared to elbow fittings and the plastic is very strong and rigid.
Highly recommended as an essential accessory for any dust collection system.
Does a Great Job January 31, 2004
Bob Feeser (Springfield, PA USA)
5 out of 5 found this review helpful
When installing a dust collection system, eliminating resistance to airflow is what it is all about. The ideal is as large a pipe as possible, flowing in a straight line, without any ridges in the surface. Of course in the real world at least some of these things wind up being less than ideal. What this Jet 4" Y-connector does, is give you a large pipe, that makes a gradual Y as opposed to a straight 90 degree angle T, and the sides of the connector are smooth. So when you need to divide your air source into two lines, this elbow does the nicest job.
The advantage of incorporating a Y connector into your system, is that you can take a single air source, connect this Y connector to it, a pair of gates, and no longer have to switch your hoses between two different pieces of equipment. All you do is open the gate to one, and close it to the other. All in all highly recommended.
 A Strong Link in the DC Chain November 14, 2001
David Lindamood (Cadillac, Michigan United States)
12 out of 12 found this review helpful
This is a good connector for a DC system. Not a complicated piece, but a very good one. The ends were all 4" , the hose fit snuggly and the wire clamps held.When making a branch in the DC system, to go to several different pieces of equipment, the "Y" connection is better to use than the "T". The Y will allow for a better air flow. Combine the Y with a/several blast gates, then it's almost like having a single hose go to each piece of equipment.
|
|
|
| |
